Microha? MK2R+ Setup Guide

Setting up N1MM loggerwith the microham MK2R+N1MM logger Version: 7.11.0microHAM Router Version: 5.03Last update: November 22, 2007Copyright 2007, Tho

microphones as they generally run much higher "mic gain" levels which increases sensitivity at theline in.1.10 Realtek sound card drivers an

Click on the Audio tab first. Set the USB Voice CODEC as the Default device for BOTH playback andRecording, and click Apply, then OK out. Now click th

1.10.4 Two soundcards installed (disable Realtek and use the other..)The issue with the RealTek HD Audio system is that RealTek creates two separate m

2 PA1M − MK2R+ and N1MM logger setupNB. This setup is not maintained anymore since beginning 2008.This setup is for personal use at the stations PA1M

2.2 microHAM Router setupTab: Ports Radio: Assign Radio 1 to COM4 and Radio 2 to COM5• Click the Set button for each radio and select the radio on t

Tab: Audio SwitchingRadio 1 − TS−2000 Radio 2 − TS−850CW: AAA (always)VOICE: CmCmCm (mic inMK2R+) CmCmA (mic insoundcard)FSK/DIGITAL: ?????V

Tab: Audio MixerRules for audio playback are: Click on "get ID" in router's audio mixer tab. Make sure that WAVE IN ID == WAVE OUT ID =

Tab: PTTRadio 1 Radio 2CW: PTT1 (microphone jack)VOICE: PTT1 (microphone jack)FSK/DIGITAL: PTT2 (rear panel jack)PA PTT: SelectLNA PTT: unselectCW: PT

Tab: CW/WinkeyPaddle mode: Iambic B (Accu keyer)Swap paddles: selectNo changes needed as all other settings under control by N1MM logger.13−2−2009 2 P

Tab: CW messagesNot in use as the function keys in N1MM logger control the CW messages.Test: test CW by pressing the Test button.Tab: FSK messagesNot

Table of Contents1 General information (setting up microHAM and N1MM logger)...11.1 General informati

Tab: ACC13−2−2009 2 PA1M − MK2R+ and N1MM logger setup 18

Select Controlled by microHAM control protocol in the two drop−down boxes. Pins 6−9 and10−13 are connected to two banddecoders which drive the micr

By Pete, N4ZR: I wanted to be able to use N1MMs FocusOther function to control where the entryfocus was when I was transmitting on one radio or the o

COM 3 COM 4Winkey port Radio 1: Settings KenwoodTS−2000COM 5 COM 613−2−2009 2 PA1M − MK2R+ and N1MM logger setup 21

Radio 2: Settings KenwoodTS−2000Radio 1: PTT + footswitch AlwaysOn????COM 7 COM 8Radio 2: PTT + footswitch AlwaysOn????MK2R+ control portDigital Modes

Winkey Tab• Use 2nd Output should be checked (?????????)♦ Pin 5 Function should be PTT (unless you are using QSK)♦ 13−2−2009 2 PA1M − MK2R+ and N1MM

Mode Tab• Contest specific choices♦ SSB/CW operation♦ Mode recorded in log◊ ??????⋅ Mode sent to radio◊ Follow mode recorded in log⋅ Log mode/Radio mo

All of the sound card selection for Digital operation happens in N2AMG's Digital Interface code. It isthrough the DI that one selects the soundca

Second MMTTY: assign PTT to the second Digital port (this is Radio_2) = COM 7♦ Choose the Misc Tab• First MMTTY: Select Source Left♦ Second MMTTY: Se

Sourse♦ First MMTTY: Left◊ Second MMTTY: Right◊ Select COM−TxD (FSK) for the TX Port. ♦ If you want the option to switch between AFSK and FSK, selec

1 General information (setting up microHAM andN1MM logger)In this document information is gathered about setting up the freeware contest program N1MM

Repeat the configuration for the Second Digital Interface substituting the second virtual COM portand using Source RightClick Menu | View• Select: XYs

3 PA1T − MK2R+ and N1MM logger setupNB. This setup is not maintained anymore since beginning 2008. This setup is for personal use at the stations PA1T

3.2 microHAM Router setupTab: Ports Radio: Assign Radio 1 to COM4 and Radio 2 to COM5• Click the Set button for each radio and select the radio on t

Test: Test buttons sends test in CW on radio 1 (MK2R: PTT: green; CW/FSK red inCW rhythm)♦ Control: Assign none (LPT port is used)• Tab: Audio Switchi

Tab: Audio MixerRules for audio playback are: Click on "get ID" in router's audio mixer tab. Make sure that WAVE IN ID == WAVE OUT ID =

Tab: PTTRadio 1 Radio 2CW: PTT1 (microphone jack)VOICE: PTT1 (microphone jack)FSK/DIGITAL: PTT2 (rear panel jack)PA PTT: SelectLNA PTT: unselectCW: PT

Tab: CW/WinkeyPaddle mode: Iambic B (Accu keyer)Swap paddles: selectNo changes needed as all other settings under control by N1MM logger.13−2−2009 3 P

Tab: CW messagesNot in use as the function keys in N1MM logger control the CW messages.Test: test CW by pressing the Test button.Tab: FSK messagesNot

When using the LPT port, select Classic auto control and assign the control lines on the SO2R tab. Pin 3 for TX focus (Pin 14 is reverse) Pin 4 f

Select Pin 6 R1 Band data output and Pin 10 R2 Band data output.Tab: Functions13−2−2009 3 PA1T − MK2R+ and N1MM logger setup 37

1.2 MK2R+ 1.2.1 Proposed Virtual Port numbersNote: The absolute port numbers do not matter. The key is consistency − the same port number mustbe used

By Pete, N4ZR: I wanted to be able to use N1MMs FocusOther function to control where the entryfocus was when I was transmitting on one radio or the o

Radio 1: Settings Icom 7800 Radio 2: Yaesu FT1000mk V13−2−2009 3 PA1T − MK2R+ and N1MM logger setup 39

Radio 1: PTT + footswitchNB. DTR Alyways OFFRadio 2: PTT + footswitchNB. DTR Alyways OFFWinkey port MK2R+ control portDigital Modes Tab• Select Sound

Winkey Tab• Use 2nd Output should be checked (needed???)♦ Pin 5 Function should be PTT (unless you are using QSK)♦ 13−2−2009 3 PA1T − MK2R+ and N1MM

Mode Tab• Contest specific choices♦ SSB/CW operation♦ Mode recorded in log◊ ??????⋅ Mode sent to radio◊ Follow mode recorded in log⋅ Log mode/Radio mo

All of the sound card selection for Digital operation happens in N2AMG's Digital Interface code. It isthrough the DI that one selects the soundca

Second MMTTY: assign PTT to the second Digital port (this is Radio_2) = COM 7♦ Choose the Misc Tab• First MMTTY: Select Source Left♦ Second MMTTY: Se

Sourse♦ First MMTTY: Left◊ Second MMTTY: Right◊ Select COM−TxD (FSK) for the TX Port. ♦ If you want the option to switch between AFSK and FSK, selec

Repeat the configuration for the Second Digital Interface substituting the second virtual COM portand using Source RightClick Menu | View• Select: XYs

13−2−2009 3 PA1T − MK2R+ and N1MM logger setup 47

select the wrong input unless USB Voice CODEC is the Windows Default sound device (bad idea)because of issues with the non−standard RealTek driver. F

4 N1MM − RTTY operation / settingsN1MM logger Configurer − Mode Tab• Contest specific choices♦ Mode recorded in log♦ Always: RTTY◊ Mode sent to radio♦

MMTTY RX bandwith exactly matching the RTTY signal. The brickwall DSP filter with sharp skirtscuts everything off but the desired signal. It is clearl

While in Run mode• Right click in the DI's RX window it sends CQ♦ When a station replies left click on the call♦ Right click sends your exchange♦

Even when I am using AFSK I operate FSK−style, i.e. doing all my tuning with the radio, never withthe mouse − I just watch MMTTY's crossed ellips

to manually enter the exchange instead of just clicking on it.By Bill, W6WRT4.7 Welcome to RTTY ContestingRTTY is becoming very popular on the HF band

Good luck in the RTTY contests!4.8 Starting in SeptemberThis first part of the big 3 part CQWW fall contest is coming soon.CQWW RTTY occurs the last w

For Windows 2000 or Windows XP. right click on the Speaker Icon on the task bar and select "AdjustAudio Properties" or open "Sounds and

Save Power up settings to reinitialize the EEPROM in microKEYER, close Router to save the settingsand then restart Router.FSK or CW messagesPTT ON/OFF

higher and there will be a substantial voltage "kick" on when the relays. The relays in the StationMaster won't handle the currents req

No audio on line inCAT noise : Buzzing sort of doo doot sound in the background of the recordThis is CAT polling noise. The K3 has RF chokes in the gr